结冰风洞校准标准研究

本文按结冰风洞制冷方式、试验对象、用途性质和试验段尺寸归纳总结了结冰风洞的类型,指出校准标准主要针对的结冰风洞类型;阐述结冰风洞空气动力流场校准可以依据的3个国内外标准;介绍SAE结冰风洞校准标准中云雾场校准的主要内容;分析研究相关标准的特点和存在的不足;提出未来我国制定结冰风洞校准标准的建议。     

搅拌式风力致热装置启动性能研究

搭建搅拌式风力致热试验台,以自制的2种致热器为研究对象,使其分别在3个不同平均角加速度24.92、14.66、8.04 rad/s2下启动。通过动态扭矩测试仪和数据采集仪测试记录致热器启动阶段的相关数据。结果表明:致热器启动时所需扭矩与角加速度的一次方、转速、叶片半径的二次方成正比,同时得出这些因素之间的关系式;满负荷时,启动扭矩会出现一个峰值,且角加速度越大峰值越大,自然风必须提供峰值以上的扭矩,否则装置无法启动。     

Optimal siting and sizing of demand response in a transmission constrained system with high wind penetration

This paper describes algorithms that use demand-side management to address large-scale integration of wind power. In particular, demand response (DR) is used to manage wind power intermittency by shifting the time that electrical power system loads occur in response to real-time prices and wind availability. An economic dispatch with transmission, DR capacity and operational constraints is used to model the operation of a transmission constrained system with a high penetration of wind power. This optimization model is used to determine the optimal sizing and distribution of DR given a fixed budget for customer incentives and the installation of enabling technology. We demonstrate the effectiveness of the operational model based on a simple PJM 5-bus system and an IEEE 118-bus system. Simulation results show that transmission constraints have a greater effect on sizing of DR capacity than the location of wind power, which means that buses electrically close to congested lines tend to have higher incentives to deploy DR resources than other buses. The second part of the work examines optimal siting of technology that enables DR based on the frequency of DR based load changes, which are generally a function of the network location.     

煤磨热风管道改造的效果

中联万基水泥有限公司4500t/d熟料生产线采用SCLW4-12×13.4第四代篦冷机,煤磨热风取风口和余热发电AQC热风取风口在篦冷机同一对称位置,煤磨与余热发电系统存在争风现象,开停煤磨对余热发电系统影响较大。通过从废气管道处开孔,加装管道和电动阀,与热风管道汇合通往煤磨沉降室,调整相应阀门开度,可以控制入煤磨烟气温度,这样不但提高了余热发电量,而且提高了煤磨产量,同时也降低了窑头排风机的负荷,降低了熟料生产电耗。     

高落差粉尘扩散规律和分布特征

高溜井放矿过程中会形成强大的冲击气流引起粉尘扩散，造成严重的井下环境污染，对其进行有效治理一直是井下通风除尘的工作重心，本工作利用相似实验和数值模拟相结合的方式探究溜井放矿过程中粉尘的扩散规律和分布特征。通过改变放矿质量、矿石粒径、溜井密闭程度、含水率等因素测试不同条件下气流大小和粉尘浓度分布，并利用CFD-DPM耦合方法模拟卸矿过程中的气?固两相流，研究气流和粉尘浓度时空分布特征。结果表明，最大粉尘浓度和风速随放矿质量增加而上升，随颗粒粒径和溜井密闭程度增大而降低，且含水率越大，粉尘浓度越小，风速无明显变化，在放矿过程中矿石颗粒之间碰撞占主导作用，颗粒流呈横向分布。     

Design and Fabrication of Concentration‐Gradient Generators with Two and Three Inlets in Microfluidic Chips

A simple and low‐cost method for designing and fabricating concentration‐gradient generators with two and three inlets is proposed which can generate different concentration gradients at varying flow velocities. The microchannel structure was designed in S‐shape and left‐right symmetry. The concentration‐gradient generator was simulated based on the finite element method. The microchannels were processed on a computer numerical control (CNC) engraving and milling machine on poly(methylmethacrylate) substrate, and then two concentration‐gradient generators were fabricated by hot bonding technology. The results of experiment and simulation were compared to prove the feasibility of the method. Flow velocity was an important factor for generating different concentration gradients. The concentration‐gradient profiles of the generators with two and three inlets present approximately linear and quadratic curves.     

A simple model for deep dynamic stall conditions

The present study is focused on modeling of dynamic stall behavior of a pitching airfoil. The deep stall regime is in particular considered. A model is proposed, which has a low implementation and computational complexity but yet is able to deal with different types of dynamic stall conditions, including those characterized by multiple vortex shedding at the airfoil leading edge. The proposed model is appraised against an extensive data set of experimental (α,C_L) curves for NACA0012. The results of an existing widely used model, having comparable complexity, are also shown for comparison. The proposed model is able to well reproduce not only the classic curves of deep dynamic stall but also the curves characterized by lift oscillations at high angles of attack due to the shedding of multiple vortices. Furthermore, the model appears to be robust to variations of its parameters from the optimal values and of the airfoil geometry. Finally, the model is successfully implemented in a commercial CFD software and applied to the simulation of a vertical axis wind turbine within the actuator cylinder approach. The accuracy of the prediction of the turbine power coefficient in the whole rotation cycle is very good for the optimal working condition of the turbine, for which the model parameters were calibrated. Fairly good accuracy is also obtained in significantly different working conditions without any further calibration.     

Design structure matrix (DSM) method application to issue of modeling and analyzing the fault tree of a wind energy asset

The perpetual energy production of a wind farm could be accomplished (under proper weather conditions) if no failures occurred. But even the best possible design, manufacturing, and maintenance of a system cannot eliminate the failure possibility. In order to understand and minimize the system failures, the most crucial components of the wind turbines, which are prone to failures, should be identified. Moreover, it is essential to determine and classify the criticality of the system failures according to the impact of these failure events on wind turbine safety. The present study is processing the failure data from a wind farm and uses the Fault Tree Analysis as a baseline for applying the Design Structure Matrix technique to reveal the failure and risk interactions between wind turbine subsystems. Based on the analysis performed and by introducing new importance measures, the “readiness to fail” of a subsystem in conjunction with the “failure riskiness” can determine the “failure criticality.” The value of the failure criticality can define the frame within which interventions could be done. The arising interventions could be applied either to the whole system or could be focused in specified pairs of wind turbine subsystems. In conclusion, the method analyzed in the present research can be effectively applied by the wind turbine manufacturers and the wind farm operators as an operation framework, which can lead to a limited (as possible) design‐out maintenance cost, failures' minimization, and safety maximization for the whole wind turbine system.     

Automated classification of simulated wind field patterns from multiphysics ensemble forecasts

In this study, we have proposed an automated classification approach to identify meaningful patterns in wind field data. Utilizing an extensive simulated wind database, we have demonstrated that the proposed approach can identify low‐level jets, near‐uniform profiles, and other patterns in a reliable manner. We have studied the dependence of these wind profile patterns on locations (eg, offshore vs onshore), seasons, and diurnal cycles. Furthermore, we have found that the probability distributions of some of the patterns depend on the underlying planetary boundary layer schemes in a significant way. The future potential of the proposed approach in wind resource assessment and, more generally, in mesoscale model parameterization improvement is touched upon in this paper.     

防振条约束失效对蒸汽发生器传热管面内流弹失稳的影响研究

根据防振条布置以及面内支承连续失效个数，将防振条面内约束失效分析划分为多种工况，分析了不同工况下面内约束失效对传热管面内模态的影响，采用各位置阻尼在振型函数上进行加权平均的方法计算了各阶模态的阻尼比，进而研究了防振条面内不同约束对传热管面内流弹失稳的影响。分析结果表明，随着面内支承连续失效位置的增多，弯管段面内首阶模态频率不断降低，出现在弯管段的振型越加明显；弯管段面内首阶模态不一定是最大流弹失稳比值出现的模态，最大流弹失稳比值出现模态的振型几乎都出现在弯管段；随着面内支承连续失效位置的增多，面内流弹失稳比值不断增大，当连续3个及以上防振条面内约束失效时，将出现流弹失稳现象。